< >

0.05mm 0.07mm Embossed Aluminum Foil

Patterned aluminum roll orange peel aluminum roll: patterned orange peel roll processed with 1060 Aluminum plate as the plate base, which can adapt to the ordinary environment and is cheap. This kind of patterned aluminum coil is usually used in cold storage, floor and outer packaging.

Patterned aluminum roll orange peel aluminum roll is also known as antirust aluminum plate. Its strength is slightly higher than that of ordinary aluminum alloy patterned roll. It has certain antirust performance, but its hardness and corrosion resistance are not up to 3000 series patterned plates. Therefore, this product is applied to rust prevention with less strict requirements, such as truck models and cold storage floors.

Introduction of orange peel aluminum roll pattern aluminum roll

Since the density of aluminum is only 2.71 and the density of iron is 7.8, the weight of each square aluminum brick is less than 1/3 of that of stainless steel, which can reduce enterprise costs and reduce support pressure. Aluminum rolls with orange peel pattern have a good anti-corrosion effect. In the external environment, rain, sunshine and snow have little destructive power. Nothing can rust quickly after rain like aluminum and iron. From the above two points, it can be seen that the orange peel aluminum coil can completely replace the stainless steel material to a large extent, and the cost is low.

Contact Now

Product Details

Embossed aluminum plate can also become aluminum embossed plate, which belongs to aluminum products that form various patterns on the surface after calendering on the basis of aluminum plate. It is widely used, mainly in packaging, architecture, curtain wall, etc. Aluminum alloy is a kind of non-ferrous metal structural material widely used in industry. It has been widely used in aviation, aerospace, automobile, machinery manufacturing, shipbuilding and chemical industry. With the rapid development of science and technology and industrial economy in recent years, the demand for aluminum alloy welded structural parts is increasing, which makes the weldability research of aluminum alloy also deepen. The wide application of aluminum alloy promotes the development of aluminum alloy welding technology, and the development of welding technology expands the application field of aluminum alloy. Therefore, the welding technology of aluminum alloy is becoming one of the research hotspots. Low density of pure aluminum（ ρ= 2.7g/m3), about 1/3 of iron, low melting point (660 ℃), aluminum is face centered cubic structure, so it has high plasticity（ δ: 32~40%， ψ: 70~90%), easy to process, and can be made into various profiles and plates. Good corrosion resistance; But the strength of pure aluminum is very low, and it is in annealed state σ B value is about 8kgf/mm2, so it should not be used as structural material. Through long-term practice and scientific experiments, people have gradually strengthened aluminum by adding alloy elements and using heat treatment, which leads to a series of aluminum alloys. The alloy formed by adding certain elements can not only maintain the advantages of pure aluminum light, but also have high strength, σ B values can reach 24 ~ 60kgf/mm2 respectively. This makes its "specific strength" (the ratio of strength to specific gravity σ b/ ρ） It is better than many alloy steels and becomes an ideal structural material. It is widely used in machinery manufacturing, transportation machinery, power machinery and aviation industry. The fuselage, skin and compressor of aircraft are often made of aluminum alloy to reduce self weight.

Using aluminum alloy to replace the welding of steel plate material can reduce the structural weight by more than 50%. Aluminum alloy with silicon content between 8% and 12% is a transition zone. Both ordinary cemented carbide and diamond tools can be used. However, when using cemented carbide, tools with PVD (physical coating) method, no aluminum element and small film thickness should be used. Because the PVD method and small film thickness make it possible for the tool to maintain a sharp cutting edge (otherwise, in order to avoid the abnormal growth of the film at the edge, the edge needs to be passivated enough, and the cutting aluminum alloy will not be sharp enough), and the aluminum contained in the film material may cause the blade film to interact with the workpiece material and destroy the combination of the film and the tool matrix. Because the current superhard coating is mostly a compound of aluminum, nitrogen and titanium, it may cause edge collapse due to a small amount of peeling off of cemented carbide matrix with the film peeling off.

Painting products

(1) It can be divided into hammered aluminum plate (irregular pattern), embossed plate (regular pattern) and pre passivated aluminum oxide surface treatment plate.

(2) Such products are not painted on the surface of the plate, so the appearance requirements of the surface are not high and the price is low.